HiPath 4000 - HiPath Access SIP Trunk Connection to Xpression Voice Mail Server

1. PBX Configuration.

Note for this example configuration : 
- vSTMI IP address : 192.168.100.183
- XPR IP address : 192.168.100.35
- SIP trunk channel = 10

- STMI GW LOCAL REGISTRATION

CHANGE-ZANDE:TYPE=ALLDATA,GATEKPR=YES;

- Block Function for vSTMI IP GW card

ADD-BFDAT:33,HG3550,BCHL120,"SOCO";

CHANGE-BFDAT:CONT,33,HG3550,1,1,;

CHANGE-BFDAT:OK,33,YES;

- Board Configuration on Switching Unit, vSTMI on HiPath Access shelf 18

ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=18,SLOT=3,PARTNO="Q2330-X   ",FCTBLK=33,IPMODE=IPV4,DHCPV4=NO,DHCPV6=NO;

- vSTMI IP, protocol, for the common gw board (cgwb)

ADD-CGWB:LTU=18,SLOT=3,SMODE=NORMAL,IPADR=192.168.100.183,NETMASK=255.255.255.0,BITRATE=100MBFD,TRPRSIP=10;

CHANGE-CGWB:MTYPE=CGW,LTU=18,SLOT=3,TYPE=GLOBIF,DEFRT=192.168.100.1;

CHANGE-CGWB:MTYPE=CGW,LTU=18,SLOT=3,TYPE=LEGKDATA,GWNO=183,GWDIRNO=700183,REGEXTGK=NO;

CHANGE-CGWB:MTYPE=CGW,LTU=18,SLOT=3,TYPE=SIPTRSSA,SIPREG=NO;

CHANGE-CGWB:MTYPE=CGW,LTU=18,SLOT=3,TYPE=SIPTRERH,GWAUTREQ=NO;

CHANGE-CGWB:MTYPE=CGW,LTU=18,SLOT=3,TYPE=GWDATA,GWID1="GW183";

- Class Of Service for the vSTMI trunk (COSSU)

ADD-COSSU:NEWCOS=10,INFO="for SIP trunk"; 

CHANGE-COSSU:TYPE=COS,COS=10,AVCE=TA&TNOTCR&FWDNWK&TTT; 

CHANGE-COSSU:TYPE=COS,COS=10,AFAX=TA&TNOTCR&BASIC; 

CHANGE-COSSU:TYPE=COS,COS=10,ADTE=TA&TNOTCR&BASIC;

CHANGE-COSSU:TYPE=LCOSV,LCOSV=10,ALAUTH=1&&64; 

CHANGE-COSSU:TYPE=LCOSV,LCOSV=10,INFO="LCR NOT RESTRICTED";

- Classmarks Of Trunk for Call Processing (COT)

ADD-COT:COTNO=100,PAR=ANS&KNOR&CEBC&CBBN&CBFN&FWDN&IEVT&BLOC&LWNC&ATRS&TSCS&ICZO&DFNN&CFOS&NLRD&LINO&SNBE&IICB&NQPI&NCDR&NOFT&NQNP&NIN2&AMFC&PGEP&IBBA&NTON,INFO="SIP TRUNK";

- Classmark Of Parameters (COP)

ADD-COP:COPNO=100,TRK=TA,TOLL=TA,INFO="SIP TRUNK";

- Add Trunk Group

ADD-BUEND:TGRP=183,NAME="SIP TRUNK       ",NO=10;

- Add Trunk Digital Config. for RMX internal tdm side of GW

ADD-TDCSU:OPT=NEW,PEN=1-18-3-0,COTNO=100,COPNO=100,DPLN=0,ITR=0,COS=10,LCOSV=10,LCOSD=1,CCT="SIP TRUNK",DESTNO=183,PROTVAR=ECMAV2,SEGMENT=8,NNO=183,TGRP=183,SRCHMODE=DSC,INS=Y,DEV=HG3550IP,BCHAN=1&&10,BCNEG=N,BCGR=1,LWPAR=0;

- Restart vSTMI module

RESTART-BSSU:ADDRTYPE=PEN,LTU=18,SLOT=3;

- Add GW internal number
ADD-GKREG:GWNO=183,GWATTR=INTGW&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="INTERNAL GW 1-18-3-0";


- Add External GW number (Xpression)
ADD-GKREG:GWNO=35,GWATTR=SIP&EXTGW,GWIPADDR=192.168.100.35,GWDIRNO=700035,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="XPRESSION";

- SIP Trunk profile configuration

Logon to vSTMI web configuration --> Explorer --> Voice Gateway --> SIP Trunk Profile Parameter - Uncheck "Use Profile for trunk via Native SIP" - Click on the diskette icon to save the configuration. - Click on Restart icon

- LCR Configuration (Close Numbering)

ADD-WABE:CD=0035,CPS=0,DAR=NETRTE,CHECK=N;

ADD-RICHT:MODE=CD,LRTE=35,CD=0035,CPS=0,SVC=ALL,NAME="XPRESSION",TGRP1=183,DESTNO=35,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="CONNECTED",DNNO=35,ROUTOPT=YES,PDNNO=35;

ADD-LODR:3,,,,ECHOALL;

ADD-LODR:3,,,,END;

ADD-LDAT:LROUTE=35,LSVC=ALL,TGRP=183,ODR=3,LAUTH=1,DNNO=35,GW1=35-0;

ADD-WABE:CD=7011&&7019,DAR=STN,CHECK=N;

CHANGE-WABE:CD=7011&&7019,DESTNO=35;

ADD-RICHT:MODE=PM,IDX=10,SAN=7013,NAME="XPRESSION",STYPE=XPRESION;

- Subscriber configuration for Voicemail user

CHANGE-SBCSU:STNO=1800,OPT=OPTI,PMIDX=10;

ADD-ZIEL:TYPE=FWD,SRCNO=1800,SI=VCE,DESTNOF=6902,NAME="XPRESSION",DTYPE=CFB&CFNR,ITYPE=GEN,CFVAR=SYSTEM;

ADD-ACTDA:TYPE=STN,STNO=1800,FEATCD=FWD,CFVAR=SYSTEM,SI=VCE;

2. OpenScape Xpression Configuration

Logon XPR monitor --> ipApl --> Advance Setting --> Device --> 03 SIP Protocol Stack - SIP Proxy IP address = vSTMI IP address - Own IP address = XPR IP address - Act as SIP trunk - Protocol = UDP

XPR monitor --> ipApl --> Advance Setting --> Extensions Tab Add New Extension Rang for Expression Phonemail Protocol (Voicemail Function)

XPR monitor --> ipApl --> Advance Setting --> Extensions Tab Add New Extension Rang for Voice Guide Script Protocol (Auto Attandant Function)

XPR monitor --> ipApl --> Advance Setting --> Protocol Tab Enter Access Code for Direct Access , Forward Access and Callback Access in Xpression Phonemail Protocol

XPR monitor --> ipApl --> Advance Setting --> Protocol Tab --> Message Waiting Indicator Enter Callback Access Code in Private tab

XPR monitor --> ipApl --> Advance Setting --> Protocol Tab --> VoiceGuide Script Enter Script Parameter "acceptcall=EARLY"